Experiencing spray issues with your Bissell Proheat 2x Revolution Pet carpet cleaner can be frustrating, especially when you’re trying to tackle pet messes. A carpet cleaner without proper spray function is essentially just a vacuum, missing out on the deep cleaning power you expect. Fortunately, many spray problems are easily resolved with a few simple troubleshooting steps. This guide will walk you through common causes and solutions for no or low spray issues with your BISSELL ProHeat 2X Revolution Pet, ensuring you can get back to effectively cleaning your carpets and removing pet stains.
Identifying and Resolving Spray Problems on Your BISSELL ProHeat 2X Revolution Pet
Before diving into detailed steps, it’s important to pinpoint where you’re experiencing the spray issue. Is the problem with the spray from the foot of the machine, or when using the hose and tools? Knowing this will help narrow down the troubleshooting process. Let’s explore the common culprits and how to fix them, ensuring your BISSELL ProHeat 2X Revolution Pet operates at its best.
Step 1: Inspecting the Clean Water Tank
The clean water tank is the lifeline of your carpet cleaner’s spray function. A damaged or improperly installed tank is a frequent cause of spray issues.
Important Note: Avoid using excessively hot water or microwaving the clean water tank. This can warp the plastic, leading to leaks and spray problems due to a poor seal between the tank and the machine.
- Power Off and Unplug: Always begin troubleshooting by turning your BISSELL ProHeat 2X Revolution Pet OFF and unplugging it from the power outlet for safety.
- Fill the Clean Water Tank: Remove the clean water tank and fill it with water and your preferred BISSELL cleaning formula according to the machine’s instructions.
Filling the clean water tank of a BISSELL ProHeat 2X Revolution Pet carpet cleaner.
Close-up of the red valve on the bottom of a BISSELL ProHeat 2X Revolution Pet clean water tank.
- Check for Damage: Carefully inspect the clean water tank for any cracks, warping, or other damage. Pay close attention to the bottom and sides of the tank.
- Test the Valve: Push up on the red valve located at the bottom of the clean water tank. Ensure that water flows freely when the valve is open. A blocked valve can prevent water from reaching the spray nozzles.
- Reinstall the Tank Securely: Place the clean water tank back onto the machine, firmly pushing it into place. Make sure there are no gaps between the tank and the machine body. An improper seal can prevent the machine from drawing water.
Reinstalling the clean water tank onto a BISSELL ProHeat 2X Revolution Pet carpet cleaner, ensuring a secure fit.
Step 2: Cleaning the Spray Tips
Clogged spray tips are another common reason for spray issues. Mineral deposits from hard water or dried cleaning solution can block the nozzles, hindering or stopping the spray.
To clean the spray tips, you first need to identify your model type, which determines the nozzle configuration.
- Locate Your Model Number: Find the information label on your BISSELL ProHeat 2X Revolution Pet. The model number is crucial for identifying the correct nozzle type and cleaning procedure.
- Remove the Nozzle Brush Cover: The method for removing the nozzle brush cover depends on whether your model number starts with 1 or 2, or with 3.
| Model Starts with 1 or 2 | Model Starts with 3: Nozzle & Cover Combined |
|---|---|
| – Detach Nozzle: Pull up on the nozzle release latch to remove the nozzle. |
- Clean the Spray Tips: Once the nozzle or brush cover is removed, you can access the spray tips.
| Model Starts with 1 or 2 | Model Starts with 3: Nozzle & Cover Combined |
|---|---|
| – Locate Spray Tips: The spray tips are located on the underside of the brush cover. – Remove Debris: Remove any visible debris from the spray tips. Use a cloth or an old toothbrush to gently scrub away any blockage. – Rinse Nozzle: Rinse the nozzle under running water, allowing the water to flow through the spray tips to dislodge any remaining blockage. – Rinse Nozzle: Rinse the integrated nozzle under water, ensuring water flows through the spray tips. |
Step 3: Testing for Spray
After cleaning the spray tips and reassembling the nozzle, test if the spray function has been restored.
- Prime the Pump: Switch between all cleaning modes on your BISSELL ProHeat 2X Revolution Pet five times. Move the switch all the way up and down repeatedly. This helps prime the spray pump and remove any airlocks.
Switching between cleaning modes on a BISSELL ProHeat 2X Revolution Pet to prime the spray pump.
- Select Max or Deep Clean Mode: Ensure the machine is set to either the MAX Clean or Deep Clean mode. These modes dispense more water than the Express Clean mode, making it easier to observe the spray.
Cleaning mode selection panel on a BISSELL ProHeat 2X Revolution Pet, highlighting Max Clean and Deep Clean modes.
- Hold Trigger and Check for Spray (Machine OFF): With the machine still turned OFF, hold the spray trigger for 15 seconds. Observe the spray port at the foot of the machine to see if water is flowing.
Holding the spray trigger on a BISSELL ProHeat 2X Revolution Pet.
Visual timer indicating 15 seconds for testing spray function.
Checking the spray nozzle for water flow on a BISSELL ProHeat 2X Revolution Pet.
- Check for Water Flow: Is water spraying from the spray port after holding the trigger for 15 seconds?
- No Spray? If there is still no spray, continue to the next troubleshooting steps or consider contacting BISSELL support for further assistance.
- Spray Restored? If water is spraying, proceed to testing the spray function while cleaning.
Step 4: Inspecting the Spray Nozzle on the Foot
If you’re still experiencing issues, the spray nozzle on the foot of the machine itself might be blocked.
- Remove Hose: Detach the hose from the foot of the machine by pressing the hose release button and gently pulling the hose away.
Removing the hose from the foot of a BISSELL ProHeat 2X Revolution Pet.
- Remove Foot Nozzle: Remove the nozzle from the foot of the machine. The removal method may vary slightly depending on your model, but typically involves releasing clips or latches.
Removing the nozzle from the foot of a BISSELL ProHeat 2X Revolution Pet.
- Prime Spray Port: Locate the spray port underneath where the nozzle was attached. Use a pen or a similar-sized object to gently insert into the port until water begins to flow out. This helps clear any blockages within the spray port itself.
Priming the spray port on the foot of a BISSELL ProHeat 2X Revolution Pet with a pen to clear blockages.
- Reassemble Foot Nozzle: Reattach the nozzle to the foot of the machine, ensuring it is securely locked in place.
| Model Starts with 1 or 2 | Model Starts with 3: Nozzle & Cover Combined |
|---|---|
| – Insert Brush Cover: Insert the brush cover until it clicks into place. Push on both sides of the nozzle to ensure it is fully installed. |
- Clean and Reattach Hose: Clean the end of the hose and reattach it to the foot of the machine. Ensure the hose release clip is facing away from the machine for proper connection.
Close-up of the nozzle on the hose insert of a BISSELL ProHeat 2X Revolution Pet.
Attaching the hose to the foot of a BISSELL ProHeat 2X Revolution Pet.
- Clean Hose Tool Spray Tip: Remove any tool attached to the hose by pressing the release button. Inspect and clean the spray tip on the hose handle itself, as this can also become clogged.
Cleaning the spray tip on the hose handle of a BISSELL ProHeat 2X Revolution Pet.
Step 5: Testing Spray from the Hose
Test the spray function through the hose to isolate whether the issue is with the hose or the foot of the machine.
- Prepare for Hose Spray Test: With any tools removed from the hose, plug in and turn ON your BISSELL ProHeat 2X Revolution Pet.
- Lay Hose Flat: Lay the hose flat on the ground or below the level of the clean water tank. This helps with priming and water flow.
- Hold Spray Trigger (Hose): Press and hold the spray trigger on the hose handle. Keep the trigger pressed to allow the machine to prime and dispense water through the hose.
Holding the spray trigger on the hose handle of a BISSELL ProHeat 2X Revolution Pet to test spray function.
Spraying with a tool attached to the hose of a BISSELL ProHeat 2X Revolution Pet (tool removed for this test).
Step 6: Testing Spray at the Foot
Finally, test the spray function at the foot of the machine to ensure everything is working correctly for carpet cleaning.
- Prepare for Foot Spray Test: Plug the machine into an outlet and turn it ON.
- Recline Handle: Recline the handle of your BISSELL ProHeat 2X Revolution Pet as you would for normal carpet cleaning operation.
- Set to Max Clean Mode: Select the Max Clean mode. This mode provides the highest water and formula dispensing for optimal spray visibility during testing.
- Hold Trigger and Move Machine: Hold the spray trigger for 15 seconds. Slowly move the machine forward and backward over the same area about three times. Move at a slow pace (approximately 8 inches or 20 cm per second) to allow for even spray distribution and proper suction.
Holding the spray trigger on a BISSELL ProHeat 2X Revolution Pet during operation.
Visual timer indicating 15 seconds for testing spray function at the foot.
Step 7: Checking for Spray Effectiveness
Observe the results to confirm if the spray issue is resolved and the machine is functioning correctly.
- Check Dirty Water Tank: Solution should flow through the front nozzle and into the dirty water tank as you clean.
- Inspect Carpet Wetness: Place your hand on the cleaned area of the carpet to check for dampness. If the carpet is wet, it indicates that the machine is spraying effectively.
Still Having Spray Issues?
If you’ve followed these troubleshooting steps and your BISSELL ProHeat 2X Revolution Pet is still not spraying correctly, it may indicate a more complex issue. In such cases, it’s best to reach out to BISSELL customer support for advanced assistance and potential repair options. They can provide specific guidance related to your model and issue, ensuring you get the help you need to keep your carpets clean and pet-mess-free.
